if you want to remove an article from website contact us from top.

    isometric view of cube is drawn the angle between the edge of cube and horizontal will be

    Mohammed

    Guys, does anyone know the answer?

    get isometric view of cube is drawn the angle between the edge of cube and horizontal will be from screen.

    The service is unavailable.

    स्रोत : gtu-mcq.com

    Isometric view of cube is drawn the angle between the edge of cube and

    Isometric view of cube is drawn the angle between the edge of cube and from EGR 120 at Algoma University

    Isometric view of cube is drawn the angle between the

    Algoma University EGR 120 jaywhiteny2k 13

    This preview shows page 3 - 6 out of 13 pages.

    456. Isometric view of cube is drawn the angle between the edgeof cube and horizontal will beA. 15 degreesB. 120 degreesC. 45 degreesD. 30 degreesD.30 degreesexplanation:-isometric view of cube is drawn the angle betweenthe edge of cube and horizontal will be 30 degrees because as theangle between the base and axis lower to will be 90 degrees theangle between the axes is 120 degrees. 120-90 = 60 degrees.

    457. Isometric view of cube is drawn the angle between the edgeof cube and vertical will be

    Get answer to your question and much more

    458. The true length of line is 40 cm and isometric view of it isdrawn the length would decrease to

    Get answer to your question and much more

    459. The true length of the line is 30 cm and isometric view isdrawn. How much length is reduced?

    Get answer to your question and much more

    Upload your study docs or become a

    Course Hero member to access this document

    Upload your study docs or become a

    Course Hero member to access this document

    End of preview. Want to read all 13 pages?

    Upload your study docs or become a

    Course Hero member to access this document

    Term Spring Professor rassai Tags

    Triangle, Isometric Projection, Isometric View, Value Of The Ratio Of Isometric Length

    Report

    Students also studied

    Bookmarked 0 Recently viewed

    EGR 120

    ratio of isometric length to true length.docx

    Viewing now

    Interested in ratio of isometric length to true length.docx

    ?

    Bookmark it to view later.

    Other Related Materials

    Other Related Materials Newly uploaded documents

    2 pages

    What are your thoughts on domestic tourism (1).docx

    38 pages

    Dimensionality reduction is usually intended to improve computational efficiency

    document 3 pages

    Ahmed Bahaa Assign 2 .pdf

    6 pages

    DNA is replicated at this time of the cell cycle A G0 B G1 C S D G2 E M 11 The

    document 4 pages

    LABWORK 1 PHYSICS.pdf

    2 pages

    Alec Beatty M03 Part A Assignment - Project Estimators.docx

    176 pages

    Preparing Multimedia Presentation In this digital age communication is mediated

    document 2 pages

    Mid Term Prep - Inferno.docx

    3 pages

    Prison Reform Draft.pdf

    12 pages

    2021-undergraduate-programs-jsom-business-administration.pdf

    26 pages

    Theron v Minister of Correctional Services.pdf

    13 pages Ch2_sec_2.pdf 15 pages

    Indirect costs There can be many indirect costs of doing business including

    document 362 pages

    even to the disjointing of our members For it is far better for the sons of God

    document 183 pages

    obligation to use BlackRock indices Any Fund that enters into a license for a

    document 2 pages 1233.pdf 600 pages

    and educationtraining standards In the fi eld of counselling in Canada the CCA

    document 26 pages

    BIO267_03.08.21_b.txt

    1 pages 18_43.pdf 1 pages

    Best D Inc - Bayport 3183 - 3.pdf

    26 pages

    QUESTION 75 When discussing the Receivables to Ledger Reconciliation Report with

    document 15 pages

    B 2000 200 C 100000 7000 D 7500 500 Select one a Region A b Region B c Region C

    document 10 pages

    12-12-2022 Ejercicios.xlsx

    assignment 1 pages p166.PNG Show More

    स्रोत : www.coursehero.com

    Isometric Axes, Lines & Planes Questions and Answers

    This set of Engineering Drawing Multiple Choice Questions & Answers (MCQs) focuses on “Isometric Axes, Lines and Planes”. 1. The angle between the isometric axes is __________ a) 180 degrees b) 60 degrees c) 90 degrees d) 120 degrees 2. The value of the ratio of isometric length to true length is ________ a) 0.141 ... Read more

    Engineering Drawing Questions and Answers – Isometric Axes, Lines and Planes

    « Prev Next »

    This set of Engineering Drawing Multiple Choice Questions & Answers (MCQs) focuses on “Isometric Axes, Lines and Planes”.

    1. The angle between the isometric axes is __________

    a) 180 degrees b) 60 degrees c) 90 degrees d) 120 degrees View Answer

    2. The value of the ratio of isometric length to true length is ________

    a) 0.141 b) 0.372 c) 0.815 d) 0.642 View Answer

    3. The length in isometric drawing of line is 20 cm. What is the true length of it?

    a) 24.53 cm b) 15.46 cm c) 19.31 cm d) 23.09 cm View Answer

    Sanfoundry Certification Contest of the Month is Live. 100+ Subjects. Participate Now!

    advertisement

    4. The true length of edge of cube is 15 cm what will be the isometric length?

    a) 17.78 cm b) 14.48 cm c) 12.99 cm d) 12.22 cm View Answer

    5. The lines parallel to isometric axes are called ________ lines.

    a) parallel b) auxiliary c) isometric d) oblique View Answer

    Check this: Engineering Drawing Books

    6. The planes parallel to any of the two isometric lines are called ________ planes.

    a) parallel b) auxiliary c) isometric d) oblique View Answer

    7. Isometric view of cube is drawn the angle between the edge of cube and horizontal will be______

    a) 15 degrees b) 120 degrees c) 45 degrees d) 30 degrees View Answer advertisement

    8. Isometric view of cube is drawn the angle between the edge of cube and vertical will be______

    a) 15 degrees b) 120 degrees c) 60 degrees d) 30 degrees View Answer

    9. The true length of line is 40 cm and isometric view of it is drawn the length would decrease to ______

    a) 28.28 cm b) 32.6 cm c) 34.6 c d) 38.63 cm View Answer advertisement

    10. The true length of the line is 30 cm and isometric view is drawn. How much length is reduced?

    a) 24.45 cm b) 25.98 cm c) 4.01 cm d) 5.55 cm View Answer

    11. The objects we see in nature will be in Isometric view.

    a) True b) False View Answer

    12. Isometric view of cube is drawn the angle between the adjacent edges is _________

    a) 90 degrees, 120 degrees

    b) 60 degrees, 120 degrees

    c) 120 degrees, 120 degrees

    d) 90 degrees, 30 degrees

    View Answer

    13. Isometric view of cube is drawn and faces of cube are seen as ___________

    a) square b) rectangle c) rhombus d) parallelogram View Answer

    Sanfoundry Global Education & Learning Series – Engineering Drawing.

    To practice all areas of Engineering Drawing, here is complete set of 1000+ Multiple Choice Questions and Answers.

    « Prev - Engineering Drawing Questions and Answers – Intersection of Surfaces

    » Next - Engineering Drawing Questions and Answers – Isometric Drawings

    Next Steps:

    Get Free Certificate of Merit in Engineering Drawing

    Participate in Engineering Drawing Certification Contest

    Become a Top Ranker in Engineering Drawing

    Take Engineering Drawing Tests

    Chapterwise Practice Tests: Chapter 1, 2, 3, 4, 5, 6, 7, 8, 9, 10

    Chapterwise Mock Tests: Chapter 1, 2, 3, 4, 5, 6, 7, 8, 9, 10

    Related Posts:

    Buy Engineering Drawing Books

    Apply for Engineering Drawing Internship

    Apply for 1st Year Engineering Subjects Internship

    advertisement

    Recommended Articles:

    Engineering Drawing Questions and Answers – Isometric Drawing of Planes or Plane Figures

    Engineering Drawing Questions and Answers – True Length of a Straight Line and its Inclinations with the Reference Planes

    Machine Drawing Questions and Answers – Isometric Drawing & Grid

    Engineering Drawing Questions and Answers – Line contained by a Plane Perpendicular to Both the Reference Planes

    Civil Engineering Drawing Questions and Answers – Isometric Projection

    Engineering Drawing Questions and Answers – Projection of Solids with Axes Inclined to both Horizontal and Vertical Plane

    Engineering Drawing Questions and Answers – Projection of Line Inclined to both the Planes

    Engineering Drawing Questions and Answers – Basics of Planes

    Engineering Drawing Questions and Answers – Projection of Straight Lines Parallel to Plane

    Engineering Drawing Questions and Answers – Projection of Planes Inclined to one of the Reference Plane & Perpendicular to other

    advertisement

    Additional Resources:

    Engineering Drawing MCQ Questions

    Civil Engineering Drawing MCQ Questions

    Machine Drawing MCQ Questions

    Mining Engineering MCQ Questions

    Civil Engineering MCQ Questions

    Popular Pages:

    Metallurgical Engineering MCQ Questions

    Marine Engineering MCQ Questions

    Aeronautical Engineering MCQ Questions

    Aerospace Engineering MCQ Questions

    Mechanical Engineering MCQ Questions

    स्रोत : www.sanfoundry.com

    Do you want to see answer or more ?
    Mohammed 16 day ago
    4

    Guys, does anyone know the answer?

    Click For Answer